Cisco has been and is a brand name whenever you look for router services. The two lines of wireless devices Linksys and Cisco Valet are both popular and used in home networks and for using Internet from the systems with the help of wireless adapters. Both have different setups and configuration process.
But here will talk about that set up page which lets the user to access the built-in web-based device for customizing settings and setting up advanced properties. Please keep in mind before accessing the device ensure that you have powered on the router plus the computer system is wired to any of the Ethernet ports on device. First you need to access the web browser. Either Google Chrome, Mozilla Firefox or Internet Explorer. Follow the steps: a. First you need to access the web browser. Either Google Chrome, Mozilla Firefox or Internet Explorer. b. Now at the URL bar enter the IP address of the router you are using and then press Enter. Note: In case if the device's IP address has been changed then enter the address on the Address Bar rather. Below can be the reasons for changed IP Address- 1. First of all check the IP address. 2. Now for 30 seconds, press the Reset button available at the back of the device. This process will help in resetting the device to factory defaults. U can erase any settings on router. c. A new window will appear asking you to enter a Username and Password. Now, enter Admin for Username and Password as Admin is a default detail for both username and password. And then click OK. Note: If you have changed the password of the device then enter the new password in the required field. The device password can be changed due to following reasons: 1. If you have run the device setup CD. 2. Or if you have changed it on web set up router page. In this way you can access the web based setup page of the VoIP router. Contact Cisco Support Australia for details about the VoIP router at 1-800-954-282 If you are planning to use the router and looking for guidance then get in touch with the professionals at Cisco support number 1-800-954-282. Our experts are here to help you 24/7 via live chat. Also Read: Cisco Router Helpline Australia Assisting Aussies In Resolving Modem Errors Related Keywords: How do I find the IP address of my Cisco router? How do I change my password on my Cisco router?
0 Comments
The Cisco 3925 router plays an important role in networking equipment produced by Cisco, which has been a network equipment giant for many years. Used 3925 routers are available on the Internet at reasonable prices, so acquiring one is not so difficult. However, if you’re Cisco 3925 Router password will be lost or forget by you then reconfiguration become impossible until it will not reset or recovered. For facing such difficulty, Cisco has built in a procedure for rescuing lost or forgotten passwords or entering new passwords by providing the following steps. Moreover, we also provide these instructions on Cisco Router Tech support Australia, through our talented technical experts. You will require Serial to RJ-45 cable and Terminal emulation software.
Step1- Connect your computer to the router with the blue serial-to-RJ-45 cable that came with the router. The 9-pin D-shell end connects to your computer's serial port, while the RJ-45 end connects to the console jack on the router. The RJ-45 end resembles a slightly larger telephone jack connector. Step2- Turn on your computer and establish a terminal session to the 3925. You can use any terminal emulator and many are freely available on the Internet. Configure the session settings as follows: 9600 baud 8 data bits No parity 1 stop bit No flow control Step3- Plug the router's power cables into an electrical outlet and as the 3925 boots, you should see the Cisco boot messages. If you don't see any output on your computer's terminal session, check your settings on the session and restart it if necessary. Press "Break" within 30 seconds of powering on the router to enter rommon (ROM monitor) mode. Step4- Type "confreg 0x2142" and press "Enter" at the "rommon 1>" prompt. This will cause the router to boot from its internal flash memory without loading the configuration into memory. At the following "rommon 2>" prompt, type "reset" and press "Enter." This will cause the router to reload and ignore the previously saved configuration file. Step5- Respond "no" and press "Enter" when prompted for responses to enter the initial dialog or basic management setup. Type "enable" and press "Enter" at the following "Router>" prompt. This will put you into enable mode and display the "Router#" prompt. Copy the non-volatile memory into memory with the "copy startup-config running-config" command, followed by the "Enter" key. Type "sho run" at the prompt and press "Enter" to display the current configuration, including the passwords, some of which may be encrypted. Step6- Type "config t" at the prompt and press "Enter." At the "Router(config)#" prompt, type "enable secret <pswd>" -- where "pswd" is the password -- and press "Enter." At this point, your enable password is reset. Press "Ctrl" + "z" to return to the "Router#" prompt. Step7- Type "config t" at the "Router#" prompt and press "Enter." At the "Router(config)#" prompt, type "config-register 0x02102" and press "Enter" to reset the boot register to its normal setting. Press "Ctrl" + "z" to leave configuration mode. Type "copy running-config startup-config" and press "Enter" to save your changes. Reboot the router and you should be able to login with your password. You can also Contact Cisco modem support Australia 1-800-954-282 for any kind of online assistance. Original Source |
AuthorLayla Kirk Archives
October 2018
Categories |